Let us help you find a solution (800) 360-8380

Sand Filters & Multi Media Filters

Sand filters are used to remove suspended solids from water and wastewater. Because they have one layer of filter media, sand filters remove only relatively large solids (normally in the range of 40 micron and larger). The effective size of each granule of sand typically varies from 0.35mm – 1.2mm. Larger granules yield coarser filtration. Finer granules yield finer filtration.


new everfilt wp site SAND MEDIA 2

Sand filters are typically used for:

  • Irrigation water
  • Storm water
  • Cooling water
  • Swimming pool water
  • Water in fountains and other water features

Removing suspended solids smaller than 40 microns requires filters with either two or three layers of filter media. These are referred to as dual-media filters or multi-media filters. When sized properly and with the correct configuration of filter media, these filters can remove suspended solids as small as 5 micron.

new everfilt wp site SAND MEDIA SKID

Skid mounted sand media filter system. Multiple configurations available depending on flow rate and imprint area.


Units are skid-mounted, factory assembled, wired, and tested, and delivered ready for installation. Piping, valves, filter media, pressure gauges and accessories are included with filter systems. Solar power, media air scour, and rinse cycle are available as options. Filter systems are engineered to require little maintenance. A separate source of water supply or a pump for backwash are seldom needed.


new everfilt wp site SAND MEDIA 3

Dual and Multi-media filters are typically used for:

  • Industrial process water
  • Waste water
  • Potable (drinking) water

Multi-Media filter

Multi-Media filter designed for a light industrial cooling tower application.

The size of each filter, the number of filters required, and the type of filter media used depend upon:

  • how small a solid needs to be removed,
  • how dirty the water is,
  • how the water will be used once it is filtered,
  • and the source of backwash water needed to clean the filters.

Size of Solids to be Removed: The smaller the solid to be removed, the slower the water must pass through the media and the finer the granule of media must be. Very often the end user doesn’t know how small a solid must be removed. In those situations, how the filtered water will be used will determine how small a solid should be removed.



Concentration of Suspended Solids: The higher the concentration of suspended solids, the larger the diameter of the filter needs to be. All filters have a maximum concentration of suspended solids that can be managed without compromising filter performance.



Source of Backwash Water: Backwash water is used to clean the filters and flush out the suspended solids that have been trapped in the media bed. Water for backwashing can come either from the filters themselves or from an external source of clean water (such as a domestic water line or a storage tank).

If backwash water comes from the filter system, there must be more than one filter in the system. Filters are backwashed one-at-a-time. During the backwash cycle, a portion of filtered water exiting the other filter(s) in the system is used to clean the dirty filter. During these periods (which typically last for several minutes per filter), the amount of filtered effluent flowing downstream of the filter is reduced by the amount of water required for backwashing.

In cases where this temporary reduction in flow is acceptable, there will be two or more filters in the system.


If no decrease in the flow of filtered water can be accepted, then water for backwashing is supplied from an external source or the pump supplying water to the filters must be able to increase its output when backwashing is required.

Units are skid-mounted, and factory assembled, wired and tested. They are delivered ready for installation. Piping, valves, pressure gauges, filter media and accessories are included with the filter system.

Design Features of Sand and Multi-media Filters:Solar power, media air scour, and rinse cycle are available as options. Filter capacities are from 5 GPM to 14 MGD. Chemical injection packages, settling tanks, clarifiers, and disinfection units are also available.

  • 8 in. to 12 ft. diameter vessels
  • Automatic or manual operation
  • All steel construction (mild steel, 304 and 316 stainless steel)
  • Stainless steel vessel internals
  • ASME code or non-code vessels
  • Hydraulic, pneumatic or electric valves
  • High pressure and temperature options
  • Class 1, Div. 1 or 2 preparation


Everfilt offers these filters with diameters ranging from 8 inches to 12 feet. E-mail us at: everfilt@everfilt.com or call 1-800-360-8380 to speak with an applications engineer who can assist you in selecting the appropriate type and size filter to meet your requirements.

To find a solution on-line, go to our Home Page.